Issue link: https://onenorgren.uberflip.com/i/555878
1 ACTUATORS ACT-132 For further information www.norgren.com Theoretical forces, air consumption, cushioning length, holding forces C/146000, C/146100, C/146200 C/146200/P The values given in the table below show the single forces in the directions Fy and Fz and the maximum moments Mx, My and Mz. All values are applicable only for speeds of max. 0.2 m/s. A requirement for using these values is a constant movement (no jerking) of the mass over the whole stroke length of the cylinder. The reference point from which the moments for all cylinders should be calculated is the center line of the pistons. When a LINTRA ® cylinder has to take several loads and moments. an additional calculation is necessary using this formula: Loading values for LINTRA ® cylinders with double carriages Loading values applicable to a speed of ≤, 0.2 m/s. Maximum working life is normally reached below a speed of 1 m/s. * The forces and moments refers to the center of the guide. They must not be exceeded in dynamic applications. Cylinder Theoretical forces lbf (N) Air consumption ft 3 /in. (l/cm) Cushioning length Holding forces lbf. (N) of brake (on dry braking surface) Ø mm at 87 psi (6 bar) of stroke at 87 psi (6 bar) inches (mm) active (L3) at 87 psi (6 bar) passive (L4) 16 27 (120) 0.001 (0.014) 0.5 (12) – – 20 42 (188) 0.002 (0.022) 1 (26) – – 25 66 (294) 0.003 (0.035) 1 (26) 112 (5000 50 (220) 32 108 (482) 0.005 (0.056) 1.4 (35) 202 (900) 84 (375) 40 170 (754) 0.008 (0.088) 2 (50) 337 (1500) 141 (630) 50 265 (1178) 0.012 (0.137) 2.3 (60) 562 (2500) 225 (1000) 63 420 (1870) 0.02 (0.218) 2.8 (70) 899 (4000) 371 (1650) 80 678 (3016) 0.03 (0.350) 3 (75) – – Internal guide C/146000 External adjustable guide C/146100 Precision roller guide C/146200 Added caged ball linear motion guide C/146200/P Fy Fz Mx My Mz Fy, Fz Mx My, Mz Fy Fz Mx My, Mz Fy, Fz Mx My, Mz lbf. lbf. lbf in. lbf in. lbf in. lbf. lbf in. lbf in. lbf. lbf. lbf in. lbf in. lbf. lbf in. lbf in. Ø mm (N) (N) (Nm) (Nm) (Nm) (N) (Nm) (Nm) (N) (N) (Nm) (Nm) (N) (Nm) (Nm) 16 9 27 2.7 33.6 9.7 45 17.7 48.7 – – – – – – – (40) (120) (0.3) (3.8) (1.1) (200) (2) (5.5) – – – – – – – 20 20 63 8.0 106.2 31.9 106 53.1 159.3 – – – – – – – (90) (280) (0.9) (12) (3.6) (470) (6) (18) – – – – – – – 25 28 87 13.3 168.2 49.6 133 79.7 247.8 133 266 115.1 371.7 450 283 1770 (125) (385) (1.5) (19) (5.6) (590) (9) (28) (590) (1180) (13) (42) (2000) (32) (200) 32 37 113 26.6 292.1 88.5 176 150.5 380.6 176 351 221.3 566.5 899 566 3540 (165) (500) (3) (33) (10) (780) (17) (43) (780) (1560) (25) (64) (4000) (64) (400) 40 74 223 57.5 743.5 212.4 360 345.2 973.6 338 676 513.4 1416.2 899 566 3540 (330) (990) (6.5) (84) (24) (1600) (39) (110) (1500) (3000) (58) (160) (4000) (64) (400) 50 99 297 97.4 1062.1 309.8 450 575.3 1416.2 450 901 858.6 2124.3 1798 1593 7080 (440) (1320) (11) (120) (35) (2000) (65) (160) (2000) (4000) (97) (240) (8000) (180) (800) 63 155 450 177.0 2124.3 619.6 721 1062.1 3097.9 721 1441 1593.2 4602.6 1798 1593 7966 (690) (2000) (20) (240) (70) (3200) (120) (350) (3200) (6400) (180) (520) (8000) (180) (900) 80 176 518 239.0 3186.4 885.1 878 1593.2 4602.6 (780) (2300) (27) (360) (100) (3900) (180) (520) – – – – – – – Mx + My + Mz + Fy + Fz <_ 1 Mx max My max Mz max Fy max Fz max LINTRA ® PLUS Rodless cylinders 146000, 146100, 146200 Internal, external and precision roller guided Double acting