Issue link: https://onenorgren.uberflip.com/i/555875
1 ACTUATORS ACT-124 For further information www.norgren.com ISO Mountings and Accessories ø 20 - ø 320mm L TM h 14 TL ø TD e 9 UW R 2 3 2 Grease nippel up to Ø 125 mm 3 Locking screws Torque max Ø 32 & 40 mm = 6 Nm Ø 50 & 63 mm = 10 Nm Ø 80 & 100 mm = 15 Nm Ø 125 mm = 25 Nm Ø 160 & 200 mm = 40 Nm Style 'UH': It is most important that the locking screws which secure the mounting to the tie rod are tightened to the torque figures shown in the table below. For maximum energy input, consult our Technical Service. 'XV' = Distance from the piston rod shoulder to the centre of the mounting. Ø L R Ø TD e9 TL TM h14 UW XV min. XV max. lb Models 32 20 1 12 12 50 50 66 80 0.35 QA/8032/40 40 24 1.6 16 16 63 58 76 89 0.77 QA/8040/40 50 28 1.6 16 16 75 70 82 98 1.43 QA/8050/40 63 28 1.6 20 20 90 80 88 107 1.87 QA/8063/40 80 28 1.6 20 20 110 100 97 123 2.65 QA/8080/40 100 38 2 25 25 132 126 112 128 5.10 QA/8100/40 125 50 2 25 25 160 152 136 154 7.31 QM/8125/40 160 50 2.5 32 32 200 192 155 185 11.7 QM/8160/40 200 50 2.5 32 32 250 240 170 200 20.7 QM/8200/40 L TM h 14 TL ø TD e 9 UW R 8 Adjustable center trunnion - UH Conforms to ISO 15552, type MT4 For profile cylinders only* 8 locking screw * Excluding IVAC Industrial and Cleanline, PRA/862000 and PRA/882000 cylinders Note: style 'UH': It is most important that the locking screws which secure the mounting to the cylinder barrel are tightened to the torque figures shown in the table above. For maximum energy input, consult our Technical Service. Unless otherwise specified, units will be supplied with trunnion positioned at dimension 'XV' plus half the stroke length. 'XV' = Distance from the piston rod shoulder to the center of the mounting. Ø L R Ø TD e9 TL TM h14 UW Torque max. (Nm) lb Models 32 25 1 12 12 50 58 2.0 0.35 PQA/182032/40 40 28 1.6 16 16 63 65 3.5 0.77 PQA/182040/40 50 28 1.6 16 16 75 80 3.5 1.43 PQA/182050/40 63 36 1.6 20 20 90 96 5.0 1.87 PQA/182063/40 80 36 1.6 20 20 110 116 6.0 2.65 PQA/182080/40 100 48 2 25 25 132 140 6.0 5.07 PQA/182100/40 125 48 2 25 25 160 163 6.0 7.31 PQA/182125/40 Front or rear detachable trunnion FH Conforms to ISO 15552 part 2, type MT 5/6 TM h14 TL UW 1 R TD e 9 L 1 D H11 Ø Ø Dh11 L1 R Ø TD e9 TL TM h14 UW1 lb Model FH 32 30 16 1 12 12 50 45 0.44 QA/8032/34 40 35 20 1.6 16 16 63 55 0.88 QA/8040/34 50 40 24 1.6 16 16 75 65 1.32 QA/8050/34 63 45 24 1.6 20 20 90 75 2.43 QA/8063/34 80 45 28 1.6 20 20 110 100 4.20 QA/8080/34 100 55 38 2 25 25 132 120 7.72 QA/8100/34 125 60 50 2 25 25 160 145 14.3 QA/8125/34 Standard L TM h 14 TL ø TD e 9 UW R 2 Fixed Center trunnion - H Conforms to ISO 15552, type MT4 2 Grease nipple up to Ø 125 mm Note: Style 'H': These mountings are only supplied assembled complete with the cylinder. Unless otherwise specified, units will be supplied with trunnion positioned at dimension 'XV' plus half the stroke length. 'XV' = Distance from the piston rod shoulder to the center of the mounting. Ø L R Ø TD e9 TL TM h14 UW XV min. XV max. lb Models 32 20 1 12 12 50 50 66 80 0.35 QA/8032/28 40 24 1.6 16 16 63 58 76 89 0.77 QA/8040/28 50 28 1.6 16 16 75 70 82 98 1.43 QA/8050/28 63 28 1.6 20 20 90 80 88 107 1.87 QA/8063/28 80 28 1.6 20 20 110 100 97 123 2.65 QA/8080/28 100 38 2 25 25 132 126 112 128 5.07 QA/8100/28 125 50 2 25 25 160 152 136 154 7.28 QM/8125/28 160 50 2.5 32 32 200 192 155 185 11.7 QM/8160/28 200 50 2.5 32 32 250 240 170 200 20.7 QM/8200/28 250 60 3.2 40 40 320 318 193 217 39.7 QM/8250/28 320 70 3.2 50 50 400 400 215 245 66.1 QM/8320/28 Adjustable center trunnion - UH