Issue link: https://onenorgren.uberflip.com/i/555860
1 ACTUATORS ACT-64 For further information www.norgren.com 3/4", 1", and 1-1/8" bore Single and double rod end styles Rated 150 psi air -20° to 200°F (-29° to 107°C) operating temperatures FPM seals optional for higher temperatures Designed to conform with NFPA (T3.6.11) 1972. Technical data Medium: Compressed air, filtered, lubricated or non-lubricated Operation: Double acting Operating Pressure: 150 PSI (10 bar) Operating Temperature: -20° to 200°F (-29° to 107°C) Cylinder Diameters: Nominal Inch: 3/4", 1", 1-1/8" Options selector for TA, TAV, and TAE Options Substitute Stroke adjustment single piston (specify adjustment length) A(-) Stroke adjustment double piston (specify adjustment length) AA(-) Port location (other than standard)* L(-) Magnetic piston* PS Rod extension (specify length) RX(-) Stainless steel tie rods &nuts S Piston Rod (chrome plated stainless steel) SS Special Rod thread(specify length) T(-) Stainless Steel Tube TS Rod thread extension (specify length) TX(-) FPM seals V Single Acting Actuators Spring on Rod End SR Spring on Cap End SC Adjustable Cushions** Substitute Rod end only DR Cap end only DC Both ends D Stroke (inches) 0.125 - 48.000 Bore Substitute 3/4" 0.75 1" 1.00 1-1/8" 1.125 Single Rod End Models Substitute Quad ring piston seal, block – vee rod seal TA Block-vee piston and rod seals TAV Ecology piston seals and block-vee rod seal TAE Double Rod End Models Quad ring piston, block – v-rod seal DTA Block-vee piston and rod seals DTAV Ecology piston seals and block-vee rod seal DTAE Mounting Styles Substitute Side Tapped 1 Side through holes 2 Cap eye 4 Head male rabbet 5 Threaded nose 6 Cap rectangular flange 7 Head flange 8 Head flange (no pilot) 9 Rod Diameter Substitute 1/4" 1 5/16" 2 3/8" 3 1/2" 4 Note: 1/2" diameter rods are not available on Series TAE Rod End Thread Style (Specify "A" or "B" on all models) Rod Size PR Thd A Thd B 1/4 ø No Thread 1/4-28 10-32 5/16 ø No Thread 5/16-24 1/4-28 3/8 ø No Thread 3/8-24 5/16-24 1/2 ø No Thread 1/2-20 7/16-20 TA 6 - 3 A - 1.125 x 5.000 -D- PS - SS * Specify head position first followed by cap position PS option adds 1/2" to overall length. ** Add 1/2" per cushioned end to overall cylinder length. Energy Absorption Capacity of Impact Dampening Seals In./Lbs of Pounds* Stoppable at Following Speeds Kinetic Energy 6 12 24 36 48 60 Size Absorbable in/sec in/sec in/sec in/sec in/sec in/sec 3/4" 1.5 32.4 8.0 2.0 .8 .41 .23 1-1/8" 3 79.2 16 4 1.8 1 .59 *Pounds must include piston and rod assembly weight The figure above represents total stroke loss (both ends) for the pressure indicated for new cylinders. The impact dampening seals will take some compression set during operation of the cylinder and the stroke loss will decrease. To determine stroke loss for either head or cap divide the value shown by 2. Cylinder Bore PSI 3/4 1-1/16 to 1-1/8 1-1/4 1-1/2 2 2-1/2 0 .11 .12 .12 .14 .15 .17 20 .08 .09 .09 .10 .10 .12 40 .05 .06 .06 .07 .07 .08 60 .03 .04 .04 .04 .04 .05 80 .01 .02 .02 .02 .02 .02 100 0 0 0 0 0 0 Effect of Impact Dampening Seals on Total Stroke of Cylinders NFPA Interchangeable Tiny Tim TA, TAV, TAE Actuators