Issue link: https://onenorgren.uberflip.com/i/555851
1 ACTUATORS ACT-12 For further information www.norgren.com Port and Cushion Adjustment Positions (As viewed from rod end: Port standard position 1, Cushion Adjustment standard position 2.) NOTE: A Port and a Cushion Adjustment cannot be in the same position. Cylinder Order Information EJ 01 7 7 A 1- 2.00 x 6.000 - L(14)-PS-V Notes + Head cushion not availale on these bore and piston rod combinations. Additional rod sizes available upon request. Dimensions for thread sizes available on following pages. Cyl rod rod dia. bore ltr. (mm) 1-1/2 A 5/8 B+ 1 2 A 5/8 B 1 C+ 1-3/8 2-1/2 A 5/8 B 1 C 1-3/8 D+ 1-3/4 3-1/4 B 1 C 1-3/8 D 1-3/4 E 2 4 B 1 C 1-3/8 D 1-3/4 E 2 F 2-1/2 5 B 1 C 1-3/8 D 1-3/4 E 2 F 2-1/2 Cyl rod rod dia. bore ltr. (mm) 6 C 1-3/8 D 1-3/4 E 2 F 2-1/2 7 C 1-3/8 D 1-3/4 E 2 F 2-1/2 8 C 1-3/8 D 1-3/4 E 2 F 2-1/2 10 D 1-3/4 E 2 F 2-1/2 12 E 2 F 2-1/2 Series Series A Cylinder (Aluminum) A Series A Double Rod End Cylinder DA Series EA Cylinder EA Series EA Double Rod End Cylinder EDA Series J Cylinder (Steel) J Series J Double Rod End Cylinder DJ Series EJ Cylinder EJ Series EJ Double Rod End Cylinder EDJ Mounting Options Side Tapped (MS4) 01 Head Rectangular Flange (MF1) 03 Head Square (ME3) – 7" & 8" Bores 03 Cap Rectangular Flange (MF2) 04 Cap Square (ME4) – 7" & 8" Bores 04 Basic Cylinder No Mounting (MX0 05 Both Ends (4) Tie Rods Ext. (MX1) 06 Both Ends (2) Tie Rods Ext. (MX4) 6B Cap Tie Rods Ext. (MX2) 6C Head Tie Rods Ext. (MX3) 6R Removable Head Trunnion (MT1) - A & EA 7R Head Trunnion (MT1) - J & EJ 07 Removable Cap Trunnion (MT2) - A & EA 8R Cap Trunnion (MT2) - J & EJ 08 Side Lugs (MS2) 09 Center Trunnion (MT4) 10 Side End Angles (MS1) 11 Cap Fixed Clevis (MP1) 12 Side End Lugs (MS7) 15 Sleeve Nut Construction (Universal) 16 Head Square Flange (MF5) 20 Cap Square Flange (MF6) 21 Detachable Cap Clevis (MP2) 22 Cap Fixed Eye (MP3) 32 Detachable Cap Eye (MP4) 42 Spherical Bearing 52 Base Bar (Not NFPA A & EA Only) 60 Cushion in Head None 3 Non-Adjustable Cushion †5 Adjustable Cushion (Position 2) 7 Decel Cushion 9 † Standard with EA & EJ Cushion in Cap None 3 Non-Adjustable Cushion †5 Adjustable Cushion (Position 2) 7 Decel Cushion 9 † Standard with EA & EJ Additional Standard Options - See next page for full listing Stroke Adjustment A Case Hardened (50 Rc) HR Port Location position 1 standard: L(Head Cap) (specify position 1 thru 4 for head and/or cap) L(_ _) Rod Lock (passive) LE Low Friction LF Metal Rod Scraper MS Cushion Adjust Screw Location position 2 standard: N(Head Cap) (specify position 1 thru 4 for head and/or cap) N(_ _) Non-Standard Port Sizes: [specify port size for P(_H) head only, P(_C) cap only, or P(_) both head & cap] *P(_) Inducted Hardened Piston PMC Magnetic Piston – includes aluminum tube option - J & EJ PS Rod Stud RS Rod Extensions (specify length of additional rod extension) RX Stainless Steel tie-rods S 303 Stainless Steel (Hard Chrome Plated) SS Stainless Steel bushing SB Stop Tube (specify stop tube length) ST(_) Special Rod Threads (specify rod thread) T Thread Extensions (specify length of thread extension) TX FPM Seals V * Oversized ports may increase the overall length by 1/8". Consult factory for impacted models. Piston Rod Threads Type Dim ref Small Male (Solid) (std) 1 KK Intermediate Thread Male (Solid) 2 CC Female 3 KK Full Thread Male (Solid) 6 FF Plain Rod End 7 – Bore x Stroke Options 1 3 4 2 NFPA Aluminum & Steel Cylinders