Issue link: https://onenorgren.uberflip.com/i/1340287
Gripper Throat Depth Inch (mm) Flange Height Inch (mm) Working Pressure Double Sided Grip Force Up To Actuation Time PGS10C .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10D .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10E .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa)) .050±.010 sec close / <.090 sec open PGS10F .92 23.4 1.21 (30.6mm) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10R .75 19 1.03 (26.3mm) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10S .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) 050±.010 sec close / <.090 sec open PGS10T .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10U .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10V .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10W .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open PGS10Y .76 19.3 1.27 (32.3) 60 psi (413kPa) Min. – 100 psi (689 kPa) Max. 450lbs (200kgf) @ 80 psi (551kPa) .050±.010 sec close / <.090 sec open A) Verify that jaws shall open freely. Look for any irregular movement, binding, or interference. A) Remove excess grease from outer surfaces of gripper. B) No required maintenance. VIII. Cleaning and Maintenance: IX. Quality Assurance Requirements: X. Specifications: Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. © 2020 Norgren Automation Solutions, LLC Page 010 08/20 User In ructions for PGS10 and PGS11 Grippers 3. Apply Red Loctite 262 or equivalent to sensor stud, place through jaw and tighten sensor nut to 72in-lb. Cable should follow the contour of the gripper jaw Cable storage loop can be adjusted with a push/pull motion to provide more or less cable slack in gripper jaw area